Number of items: 22.
Aziz, Mohd Sharizal Abdul
(2015)
Study Of Wave Soldering Using Thermal-Fluid Structure Interaction Technique On Pin Through Hole In Printed Circuit Board.
PhD thesis, Universiti Sains Malaysia.
Hashim, Mohd Khairul Rabani
(2015)
Speech Quality Analysis For Two-Ways Radio Subjected To Wind Induced Noise.
Masters thesis, Universiti Sains Malaysia.
Jamaludin, Amirul Aliff
(2015)
An Integration Of Taguchi Method And Response Surface Methodology (Rsm) On Injection Moulded Pp Gears For Parameters Optimization.
Masters thesis, Universiti Sains Malaysia.
A
Abd Wahid, Khairul Anuar
(2015)
Synthesis And Application Of Zno Nanorods For Oxygen Gas Sensor.
PhD thesis, Universiti Sains Malaysia.
Abdul Hamid, Muhammad Najib
(2015)
Analysis of Drum Brake Squeal.
PhD thesis, Universiti Sains Malaysia.
Abdul Rashid, Azrin Hani
(2015)
Low Velocity Impact Response of Laminated Textile Coiraramids Epoxy Hybrid Composites Subjected to Transverse Penetration Loading.
PhD thesis, Universiti Sains Malaysia.
Amat Sazali , Shazrul Nizam
(2015)
Effect Of Water Injection Inside A Double Walled Throatless Downdraft Gasifier For Improving Producer Gas Quality.
Masters thesis, Universiti Sains Malaysia.
Anuar, Muhamad Shukri
(2015)
Torrefaction Of Wood Pellets Using
Heat From The Producer Gas.
Masters thesis, Universiti Sains Malaysia.
C
Chong, Zheng Ziao
(2015)
Modified Neh Heuristic On Makespan Reduction In Permutation Flow Shop Problems.
Masters thesis, Universiti Sains Malaysia.
D
Ding , Siew Hong
(2015)
Integration Of Clustering Concept And Fuzzy Topsis For Maintenance Policy Decision Making Model.
PhD thesis, Universiti Sains Malaysia.
H
Haniff, Muhammad Aniq Shazni Mohammad
(2015)
Low Dimensional Carbon Based Materials For Low Pressure Measurement Application.
PhD thesis, Universiti Sains Malaysia.
Haniff, Muhammad Aniq Shazni Mohammad
(2015)
Low Dimensional Carbon Based Materials For Low Pressure Measurement Application.
PhD thesis, Universiti Sains Malaysia.
K
Kassim, Mohd Syahir Mohd
(2015)
Optimization Of Injection Moulding Process For Hdpe Moulded Gear.
Masters thesis, Universiti Sains Malaysia.
L
Lim , Shen Chuan
(2015)
A process improvement framework integrating lean methodology and decision tools in manufacturing industry.
Masters thesis, Universiti Sains Malaysia.
Lim , Teong Yeong
(2015)
Measurement Of Nose Radius And Wear Of Multiple Cutting Tool Inserts From 2-D Scanned Images With Sub-Pixel Edge Detection.
PhD thesis, Universiti Sains Malaysia.
M
Mohd Shafie, Mohd Saiful Aizat
(2015)
Effect Of Supercharging And Turbocharging In A Multi Cylinder Low Speed Spark Ignition Engine Fuelled By Producer Gas.
Masters thesis, Universiti Sains Malaysia.
S
Samat, Hasnida Ab
(2015)
Development Of Practical Opportunistic Maintenance (Om) Policy Based Model For Manufacturing System.
PhD thesis, Universiti Sains Malaysia.
Shamsudin, Nor Fadilah
(2015)
Parametric Studies of Vbo-Oven Cure Process On The Bonding Quality Of Sandwich Panel.
Masters thesis, Universiti Sains Malaysia.
Subramonian, Sobana Raj
(2015)
Simulation On Atkinson-Miller Cycle Engine Of Four Stroke Two-Wheel Vehicle For Light Operating Condition.
Masters thesis, Universiti Sains Malaysia.
Sung , Aun Naa
(2015)
Effect Of Tool Geometry And Nose Profile Micro-Deviation On Surface Roughness In Finish Turning.
PhD thesis, Universiti Sains Malaysia.
T
Teoh , Choe Yung
(2015)
Dither Effect Of Drum Brake Squeal.
PhD thesis, Universiti Sains Malaysia.
Z
Zulkifli, Siti Syazni
(2015)
Modelling And Stress Analysis Of Lumbar Spine.
Masters thesis, Universiti Sains Malaysia.
This list was generated on Sun Dec 22 15:17:37 2024 +08.
